Dremel Столик для фрезерования Uživatelský manuál stáhnout pdf (Strana 6)

ROUTER FEED DIRECTION

Therouterspindleturnsinananticlockwisedirectionwhenviewed

fromabovethetable.Forbestcontrolandqualityofcut,feedthework

into the bit in the direction that the bit will tend to pull the work to the

fence.Feedtheworkpiecefromrighttoleftasshown.

SeeFigure6

Feeddirectionisextremelyimportantwhenusingapilotbitfreehand

on the edge of a workpiece as well as when using the fence with all

bits.

SeeFigure7a:Feed Direction without Fence

SeeFigure7b:Feed Direction with Fence

FeedDirectionArrowA

Tips Table:

Wrong Direction - Hard to control1.

Feedingtoofast-Overloadsmotor2.

Dull bit - Overloads motor3.

Cutting too large or deep in one pass - Overloads motor4.

Feedingtooslow-Leavesfrictionburnsonwork.5.

ROUTING USING THE FENCE

Unplug the rotary tool before making any fence adjustments or bit 1.

changes.Feedtheworkagainsttherotationofthebitasshown.

Most fence cutting is done with the support wedge adjusted to

the right where it is in line with the fence.

SeeFigure8:Fence

Clamp Screw NutA

FeedDirectionB

Support WedgeC

Center cylinder of the guard can be adjusted up when making 2.

cuts using the fence. Loosen thumb nut, lift the cylinder up and

secure by tightening thumb nut.

When shaping small pieces or when ﬁnishing the cut on narrow, 3.

long pieces, use a push stick. Use 5 x 50 x 200 mm (metrics)

piece of lumber notched as shown to make this push stick. It will

enable you to keep your hands away from the cutting area.

SeeFigure9:Feed Direction for Straight Cuts with Fence

Large KnobA

Center CylinderB

ThumbNutC

Push StickD

Tocutastraightgroove,installthebitandsetthedepthofcut4.

usingthedepthadjustmentknobasshowninFig.4.Loosenlarge

knob on left end of fence assembly to proper distance from bit to

givedesiredgroovelocation.Retightenlargeknob.Takeatrialcut

on scrap lumber to check depth and location of groove.

When trimming the entire edge of a workpiece, adjust the support 5.

wedgeforsupportoftheworkpieceontheleftsideofthecutter.First,

adjustthefencetocontroltheamountofcut.Takeatrialcutofabout

50mmlongandchecktheamountofcut.Turnrotarytooloff.Loosen

wedge clamp nut and slide wedge to left until wedge contacts

workpiece. Retighten clamp nut to secure wedge to fence. Workpiece

willnothavesupportonbothsidesofthecutter.(SeeFig.8)

WARNING

Place material between router bit or

accessory and fence while routing or

sanding edge.

ROUTING USING PILOT BITS

When bits with pilots are to be used, move the fence back only 1.

enough to allow the amount of cut to be made. Keeping the fence

close to the bits allows the fence to serve as a rear guard. In

special cases when the fence must be removed from the table,

adjust the centre cylinder of the guard down to provide protection

from revolving cutter.

Onlypilotedbitscanbeusedwithoutthefence.Theworkpiece2.

should be kept between the cutter and the operator, and fed from

right to left.

Feedtheworkpiecepastthecutterwithoutstoppingandwith3.

a consistent speed, A change in feed or a dwell will cause an

irregular cut.

EXPANDED TABLE WORK SURFACE

TheShaper/Routertableisdesignedtomakeiteasytoexpandthe

size of the working surface. Use 10 mm thick solid core plywood.

Cut a rectangular hole in the plywood to ﬁt over the table and secure

using (8) #10 wood screws, 12 mm in length. Support the table at

both ends by securing 40 mm high lumber supports to the plywood

base. (See Fig.10) (Hardware not included)

SeeFigure10:

40 mm A Slot to Clear Guard

RectangularHoletofitoverTableB

40 mm High Supports on Both Ends will rest on BenchC

10 mm PlywoodD

SERVICE AND WARRANTY

ThisDREMELproductisguaranteedinaccordancewithstatutory/

country-speciﬁc regulations; damage due to normal wear and tear,

overload or improper handling will be excluded from the guarantee.

In case of a complaint, send the tool undismantled together with proof

of purchase to your dealer.

CONTACT DREMEL

FormoreinformationontheDremelassortment,supportandhotline,

go to www.dremel.com

DremelEurope,P.O.Box3267,4800DGBreda,TheNetherlands

ALLGEMEINE SICHERHEITSHINWEISE

WARNUNG

SÄMTLICHE ANWEISUNGEN SIND

ZU LESEN.

Fehler bei der Einhaltung der nachstehend aufgeführten Anweisungen

können elektrischen Schlag, Brand und/ oder schwere Verletzungen

verursachen. Der nachfolgend verwendete Begriff “Elektrowerkzeug”

bezieht sich auf netzbetriebene Elektrowerkzeuge (mit Netzkabel).

BEWAHREN SIE DIESE ANWEISUNGEN GUT

AUF

ARBEITSPLATZ

a. Halten Sie Ihren Arbeitsbereich sauber und aufgeräumt. Unordnung

und unbeleuchtete Arbeitsbereiche können zu Unfällen führen.

b. Arbeiten Sie mit dem Gerät nicht in explosionsgefährdeter

Umgebung,indersichbrennbareFlüssigkeiten,GaseoderStäube

beﬁnden. Elektrowerkzeuge erzeugen Funken, die den Staub oder

die Dämpfe entzünden können.

c. Halten Sie Kinder und andere Personen während der Benutzung

des Elektrowerkzeugs fern. Bei Ablenkung können Sie die Kontrolle

über das Gerät verlieren.

1 2 3 4 5 6 7 8 9 10 11 ... 83 84

Komentáře k této Příručce

Žádné komentáře

Dremel Столик для фрезерования Uživatelský manuál Strana 6

Komentáře k této Příručce

Související produkty a manuály pro Nástroje Dremel Столик для фрезерования